RF Safety & Regulatory Guidance

Last updated: November 7, 2026

This page summarizes common radio-frequency (RF) engineering practices and general regulatory concepts for informational and educational purposes only. It does not constitute legal or regulatory advice, may not reflect current laws in your jurisdiction, and implementing the practices described on this page does not guarantee regulatory compliance. Under our Terms of Service, the Creators of RemoteRF assume no liability for how any deployment is configured or used; Deployment Operators and Users are solely responsible for verifying and maintaining compliance with all applicable spectrum laws, licenses, and institutional policies.

Because software-defined radios (SDRs) such as the ADALM-PLUTO, USRP, and HackRF One can tune across gigahertz of spectrum with programmable bandwidth and transmit gain, operating a remotely accessible SDR testbed requires careful engineering. Unlike consumer Wi-Fi routers or Bluetooth adapters, general-purpose SDRs are typically sold as laboratory test equipment or evaluation subassemblies rather than pre-certified consumer transmitters, and many low-cost SDRs lack built-in front-end harmonic filters.

To prevent harmful interference and unauthorized transmissions, responsible deployments combine three layers of defense:

  1. Physical RF Safeguards: Confining signals to coaxial cables where possible, and fitting any over-the-air (OTA) transmit port with inline hardware band-pass filters and attenuators.
  2. Software & Schema Lockouts: Enforcing strict bounds on frequency, bandwidth, and transmit gain via per-device limits in devices.yml and server-side Python device schemas (<device>_schema.py).
  3. Administrative & Regulatory Controls: Restricting access via enrollment codes, coordinating with campus spectrum managers, and securing any required regulatory authorizations before enabling OTA transmission.

Supported Hardware Power & EIRP

Spectrum regulations typically limit Effective Isotropically Radiated Power (EIRP) rather than the raw power at a radio’s connector. For connectorized SDRs, maximum EIRP depends on the radio’s conducted output power (PTX), the insertion loss of any inline coaxial attenuators, filters, and cables (Linline), and the gain of the attached antenna (Gant):

EIRP (dBm) = P_TX,conducted (dBm) - L_inline (dB) + G_ant (dBi)

For example, an ADALM-PLUTO operating at its maximum conducted output (~+7 dBm) into a 2 dBi whip antenna radiates ~+9 dBm EIRP (8 mW), which exceeds the unlicensed FCC § 15.249 limit (~−1.25 dBm EIRP). Adding a 30 dB inline SMA attenuator reduces the radiated power to ~−21 dBm EIRP (8 μW), more than 19 dB below the § 15.249 ceiling.

The table below lists typical maximum conducted output power (or integrated-antenna EIRP) across RemoteRF’s supported hardware:

Device Frequency Range Max Conducted TX Power Typical Unattenuated EIRP Regulatory & Setup Notes
ADALM-PLUTO / Pluto+ 325 MHz – 3.8 GHz (70 MHz – 6 GHz extended) ~+7 dBm (5 mW) ~+9 dBm with 2 dBi whip (−21 dBm with 30 dB inline pad) Evaluation board; lacks front-end harmonic filters. Add inline band-pass filter and 20–30 dB attenuator for OTA use.
HackRF One 1 MHz – 6.0 GHz +10 to +15 dBm (<2.1 GHz); 0 to +10 dBm (>2.1 GHz) Up to +17 dBm with 2 dBi antenna Evaluation board; strong odd harmonics. Always use an inline band-pass or low-pass filter and attenuation for OTA TX.
USRP 2901 / B205-mini 70 MHz – 6.0 GHz +15 to +20 dBm (30–100 mW) Up to +22 dBm with 2 dBi antenna Higher output power than Pluto/HackRF; clamp TX gain in schema and install inline attenuation and filtering for OTA links.
USRP N210 (SBX / WBX / UBX) DC – 6.0 GHz (daughterboard dependent) +17 to +20 dBm (50–100 mW) Up to +22 dBm with 2 dBi antenna Laboratory transceiver; requires cabled loopback, inline attenuation/filtering, or experimental licensing for OTA TX.
RFbeam K-MD7 Radar 24.075 – 24.175 GHz (24 GHz ISM) Integrated patch array (1 TX / 2 RX) +19 to +20 dBm (100 mW) max EIRP Operates inside the 24.00–24.25 GHz ISM band (FCC § 15.249 / § 15.245 & ETSI EN 300 440). Fixed PCB antenna.
TI AWR6843ISK Radar 60.0 – 64.0 GHz +12 dBm per TX channel (3 TX / 4 RX) ~+19 to +21 dBm EIRP per TX (~+26 dBm 3-TX array) Governed by 60 GHz field disturbance sensor rules (FCC § 15.255 & ETSI EN 305 550); keep chirp duty cycle ≤10%.
Bluetooth / Wi-Fi Dongles 2.4 GHz & 5 GHz Pre-certified USB modules ≤+20 dBm EIRP (BLE/Wi-Fi regulatory domain) Used primarily for passive scanning/RSSI in RemoteRF; pre-certified under FCC Part 15.247 / 15.407 when unmodified.
RTL-SDR / KrakenSDR / GPS 24 MHz – 1.766 GHz (GPS: 1575.42 MHz) Receive-only (no external TX) None (N/A) No transmitter license required; KrakenSDR internal noise source is confined to internal phase calibration.

Physical RF Safeguards

Hardware controls provide the strongest protection against accidental misuse because they physically constrain radiated energy regardless of what a user’s Python script attempts to execute.

Cabled Coaxial Loopback & Terminations

Whenever an experiment or course lab does not strictly require wireless propagation over the air, cabled coaxial loopback is the safest and most repeatable configuration:

  • Single-Device or Cross-Device Coax Links: Connect the transmit (TX) port of an SDR directly to its own receive (RX) port—or to another SDR’s RX port—using double-shielded SMA coaxial cable and an inline 30–40 dB SMA attenuator to protect the receiver front-end. Multi-tap channels can also be built using coaxial splitters, combiners, and delay lines.
  • 50 Ω Terminations on Receive-Only Radios: If a transceiver SDR (such as an ADALM-PLUTO or USRP) is intended for receive-only spectrum monitoring, remove its TX antenna and screw a 50 Ω SMA terminator cap (dummy load) onto the TX port in addition to disabling TX in software.

RF Shielded Enclosures

For short-range OTA experiments that require real antennas (such as small phased arrays or MIMO calibration) without radiating into the surrounding building, placing the antennas inside a desktop RF shielded test enclosure or anechoic box confines emissions while still allowing over-the-air coupling inside the chamber.

Inline Band-Pass Filtering & Attenuation for OTA Setups

If your deployment includes SDRs with antennas attached for over-the-air operation:

  • Always Filter OTA Transmit Ports: Many SDRs (including the ADALM-PLUTO and HackRF One) use square-wave local oscillator (LO) mixers without switched front-end filter banks. As a result, their odd harmonics (3fc, 5fc) can be only 10–15 dB below the fundamental carrier. Without a physical filter, transmitting in one band can radiate strong harmonics directly into restricted safety-of-life bands (for example, a 525 MHz fundamental produces a 3rd harmonic at 1575 MHz inside GPS L1, and a 915 MHz fundamental produces a 3rd harmonic at 2745 MHz inside aviation and weather radar spectrum). Screwing a coaxial SMA band-pass filter matched to your operating band directly onto the SDR’s TX port physically suppresses out-of-band harmonics.
  • Use Inline Attenuators & Avoid External Power Amplifiers: Inserting a 20–30 dB inline SMA attenuator before the TX antenna keeps radiated power at sub-milliwatt levels suitable for indoor benchtop links and prevents saturating nearby receivers. Avoid connecting external RF power amplifiers to remotely accessible SDRs unless operating under a dedicated spectrum license with hardware power-monitoring interlocks.
  • Use Band-Specific Resonant Antennas: Pair OTA radios with narrowband antennas resonant only in your intended operating band rather than wideband discone or log-periodic antennas.

Software & Schema Lockouts

RemoteRF allows Deployment Operators to enforce parameter limits on the server before user commands reach the physical hardware driver, using both declarative limits in devices.yml and custom rules in <device>_schema.py.

Per-Device Frequency Limits in devices.yml

In ~/.config/remoterf/devices.yml (or ~/.config/remoterf/host/devices.yml on a host), you can configure a limits block on any SDR entry to restrict permitted frequencies directly at the server level:

- device_id: 3
  device_type: adalm_pluto
  limits:
    tx_freq:
      whitelist: [[2.40e9, 2.48e9]]
      blacklist: [[2.45e9, 2.46e9]]
      on_violation: reject
      default: 2.42e9
  • whitelist: List of [min_hz, max_hz] frequency intervals where operation is allowed (for example, [[2.40e9, 2.48e9]] to confine transmission to the 2.4 GHz ISM band). Any frequency outside the whitelisted intervals triggers a violation.
  • blacklist: Optional list of [min_hz, max_hz] sub-bands to exclude even when they fall inside a whitelisted range (for example, [[2.45e9, 2.46e9]] to notch out an active campus Wi-Fi channel or sensitive laboratory instrument).
  • on_violation: Action taken when a user script requests an out-of-bounds frequency (such as reject to block the request and raise an error on the client).
  • default: Safe initial frequency applied when the device is initialized or reset (such as 2.42e9).

Custom Driver Schema Bounds (<device>_schema.py)

Because built-in RemoteRF schemas (~/.config/remoterf/drivers/<device>_schema.py) are general-purpose templates designed to work across many hardware setups, Deployment Operators should also audit and customize their active <device>_schema.py files to enforce additional operational bounds before exposing OTA devices to users:

  • Restrict Center Frequencies (tx_lo): Reject any transmit frequency outside your authorized band (plus a guard band at each edge so modulated sidebands cannot spill outside the allocation).
  • Clamp Transmit Gain (tx_hardwaregain): Enforce a safe ceiling on transmit gain (for example, capping ADALM-PLUTO tx_hardwaregain_chan0 to -10 dB or lower for indoor OTA links).
  • Bound Sample Rate & RF Bandwidth: Cap maximum sample rates and analog filter bandwidths so users cannot configure wideband emissions that exceed channel limits.
  • Disable Transmit Methods on RX-Only Devices: On devices intended only for reception, remove @idl_expose from transmit methods or raise a PermissionError if a user attempts to call tx().
# Example: Enforcing frequency, bandwidth, and TX gain bounds in a custom schema
ALLOWED_TX_FREQ_HZ = (905_000_000, 925_000_000)  # 902-928 MHz ISM with 3 MHz guard bands
MAX_TX_BANDWIDTH_HZ = 4_000_000                  # 4 MHz max bandwidth
MAX_TX_GAIN_DB = -10.0                           # Sub-milliwatt indoor TX ceiling

@idl_expose
def set_tx_lo(self, freq_hz: int) -> None:
    lo, hi = ALLOWED_TX_FREQ_HZ
    if not (lo <= int(freq_hz) <= hi):
        raise ValueError(f"TX frequency must be between {lo / 1e6:.1f} and {hi / 1e6:.1f} MHz.")
    self._sdr.tx_lo = int(freq_hz)

@idl_expose
def set_tx_gain(self, gain_db: float) -> None:
    if float(gain_db) > MAX_TX_GAIN_DB:
        raise ValueError(f"TX gain cannot exceed {MAX_TX_GAIN_DB} dB on this deployment.")
    self._sdr.tx_hardwaregain_chan0 = float(gain_db)

Because software lockouts do not suppress physical mixer harmonics or transient spikes during device initialization, always pair server-side frequency and gain limits with physical coaxial filters and attenuators on OTA radios.

Access & Institutional Controls

  • Gate OTA Radios with Enrollment Codes: Keep user groups private so only enrolled students or vetted researchers with a valid enrollment code can reserve OTA hardware. Never leave unattenuated OTA transmitters open to anonymous public access.
  • Publish Clear Operating Rules: Document the permitted frequency range, bandwidth, and gain limits for each device in your lab handouts or deployment descriptions so users know the bounds before writing code.
  • Coordinate with Campus IT & Spectrum Managers: At universities and research institutions, transmitting in the 2.4 GHz or 5 GHz bands inside classroom buildings can interfere with campus enterprise Wi-Fi networks. Consult your institution’s wireless networking team or Environmental Health & Safety (EH&S) office before bringing up indoor or outdoor OTA nodes.

United States (FCC) Considerations

In the United States, the Federal Communications Commission (FCC) regulates non-federal use of the electromagnetic spectrum under Title 47 of the Code of Federal Regulations (47 CFR). Below are the primary regulatory frameworks relevant to SDR testbeds in the U.S.:

Key Spectrum Allocations & Regulatory Significance
Unlicensed ISM / Radar Licensed / Conditional Restricted (§ 15.205 — No TX)
Sub-6 GHz Spectrum
108–138 MHz
Aviation & ELT
Air nav, voice & 121.5 MHz ELT
600–894 MHz
Cellular / SRD
US 5G/LTE; EU 863–870 SRD
902–928 MHz
Americas ISM
US/CA ISM; cellular in EU
960–1610 MHz
GNSS & Air Nav
GPS L1 (1575) & ADS-B (1090)
1.7–2.2 GHz
AWS / PCS
Licensed 4G/5G carrier bands
2.40–2.48 GHz
Global 2.4 ISM
Worldwide ISM, Wi-Fi & BLE
3.45–3.98 GHz
C-Band / CBRS
Licensed 5G & Part 96 SAS
5.72–5.85 GHz
Global 5.8 ISM
Worldwide ISM & U-NII-3 Wi-Fi
Upper Mid-Band Spectrum
5.925–7.125 GHz
6 GHz Band (U-NII-5–8)
Not ISM: requires certified LPI/CBP or AFC hardware (or Part 5 license for SDRs)
6.0–10.6 GHz
Ultra-Wideband (UWB)
Not ISM: certified Subpart F devices only (≥500 MHz BW, ≤−41.3 dBm/MHz PSD)
7.125–10.6 GHz
X-Band & Lower FR3
Federal/fixed microwave & radar (§ 15.205 restricted at 8.2–8.4 & 9.0–9.2 GHz)
10.60–10.70 GHz
Passive Sensing (EESS)
ITU 5.340 & § 15.205 passive satellite & radio astronomy — no TX permitted
10.7–23.6 GHz
Ku / K-Band & Upper FR3
Satellite (FSS), fixed backhaul & 6G FR3 research (§ 15.205 passive at 15.35–15.4 GHz)
Millimeter-Wave Spectrum
23.60–24.00 GHz
Passive Weather Satellite (EESS)
ITU 5.340 & § 15.205: all emissions strictly prohibited immediately below 24.00 GHz
24.00–24.25 GHz
24 GHz Narrowband ISM
Short-range ISM & field disturbance sensors (≤+20 dBm EIRP under § 15.249 / EN 300 440)
57.0–71.0 GHz (57–64 GHz EU)
60 GHz Unlicensed mmWave
Short-range communication & sensing (§ 15.255: ≤+20 dBm EIRP, or ≤10% duty cycle)
Illustrative overview of selected sub-6 GHz, upper mid-band (FR3), and millimeter-wave spectrum allocations. Green blocks indicate primary unlicensed ISM and short-range radar bands; amber blocks indicate licensed, regional, or conditional-access bands; red blocks indicate restricted safety-of-life and passive satellite bands where neither fundamentals nor harmonics may be radiated. This overview is neither an official frequency allocation table nor exhaustive, omits many shared and secondary services, and is subject to change as national and international spectrum regulations are updated.

Conducted vs. Over-the-Air Operation

  • Conducted Cabled Testing (47 CFR § 15.1(c)): When RF signals are confined to shielded coaxial cables, attenuators, and dummy loads without an antenna, the setup is not an intentional radiator. Provided incidental leakage from cables and connectors remains below Part 15 unintentional radiator limits, no OTA spectrum license is required.
  • Shielded Enclosures (47 CFR § 15.201(d)): Transmitters operated exclusively inside a shielded enclosure whose exterior leakage does not exceed Part 15 unintentional radiator limits are similarly exempt from external transmitter licensing.

Unlicensed ISM Band Operation (47 CFR Part 15, Subpart C)

For low-power indoor OTA setups in the United States, operators commonly restrict frequencies to the Industrial, Scientific, and Medical (ISM) bands—most notably 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz:

  • Low-Power Operation under § 15.249: Permits any modulation type in 902–928 MHz, 2400–2483.5 MHz, and 5725–5875 MHz provided the fundamental field strength does not exceed 50 mV/m at 3 meters (equivalent to approximately −1.25 dBm EIRP, or ~0.75 mW into an isotropic antenna) and harmonics remain below 500 μV/m at 3 meters (or § 15.209 limits). All Part 15 operation is strictly subject to the conditions that the device may not cause harmful interference and must accept any interference received (§ 15.5).
  • Digital Modulation / Spread Spectrum under § 15.247: Allows higher output power in the same bands, but imposes strict technical requirements (such as frequency hopping or digital modulation with a minimum 6 dB bandwidth of at least 500 kHz and a power spectral density limit) and equipment authorization requirements that general-purpose SDR waveforms often do not satisfy without a separate experimental authorization.
  • Evaluation Kits & Subassemblies (§ 2.803(c)(2)): Uncertified evaluation boards and test equipment may be operated for product development, evaluation, and research purposes by qualified personnel strictly on a non-interference basis and in compliance with applicable FCC rules.

Strictly Prohibited / Restricted Bands (47 CFR § 15.205)

Under 47 CFR § 15.205, intentional transmissions are prohibited in restricted bands protecting safety-of-life, navigation, and passive scientific services (only minimal spurious leakage below § 15.209 limits is allowed). Never allow emissions in:

  • GPS / GNSS Navigation Bands: 1164–1240 MHz and 1559–1610 MHz
  • Aviation Communications & Navigation: 108–121.94 MHz, 123–138 MHz, and 960–1215 MHz
  • Emergency & Search-and-Rescue Beacons: 121.5 MHz, 243 MHz, and 406 MHz
  • Commercial Cellular, Public Safety & Licensed Bands: Including 600/700/800 MHz, 1.7–2.2 GHz, 2.5 GHz, and 3.45–3.98 GHz

FCC Part 5 Experimental Radio Licenses (47 CFR Part 5)

Universities, colleges, and research laboratories planning over-the-air research or instruction outside low-power Part 15 limits should consider obtaining an experimental authorization from the FCC Office of Engineering and Technology (OET):

  • Program Experimental Radio License (§ 5.301–5.313): Available to accredited institutions of higher education and non-profit research organizations. It authorizes ongoing RF experimentation across broad frequency ranges within a registered campus or indoor laboratory boundary, with individual experiments registered via the FCC’s online portal prior to transmission.
  • Conventional Experimental License (§ 5.51) & Special Temporary Authority (§ 5.61): Authorize specific frequency bands, emission bandwidths, power ceilings, and coordinates for multi-year projects or short-term (up to 6-month) trials.

Why Amateur Radio Rules (47 CFR Part 97) Rarely Fit Shared Student Testbeds

Although FCC Part 97 permits remote control of an amateur station (§ 97.213), Part 97 requires that every individual operating the transmitter hold an FCC Amateur Radio license (unlicensed students may only participate when a licensed control operator is physically present with the student), requires transmitting a station call sign every 10 minutes (§ 97.119), and prohibits encryption (§ 97.113). Consequently, Part 97 cannot be used to authorize general remote classroom access by unlicensed students.

Communications Privacy & Export Controls

  • Electronic Communications Privacy (18 U.S.C. § 2511 & 47 U.S.C. § 605): Even on receive-only SDRs, federal law prohibits intentionally intercepting, decoding, or divulging non-public electronic communications (such as cellular calls or private encrypted traffic). Receiving public broadcasts, amateur radio, weather satellites, ADS-B/AIS beacons, or your own lab’s test signals is lawful.
  • Export Administration Regulations (EAR) & OFAC Sanctions: Providing remote access to certain high-performance SDR hardware or technical software to users in embargoed or sanctioned jurisdictions may implicate U.S. export control laws.

24 GHz & 60 GHz Millimeter-Wave Radar Rules

RemoteRF natively supports two short-range radar sensors—the RFbeam K-MD7 (24 GHz) and the Texas Instruments AWR6843ISK (60–64 GHz)—which operate under specialized regulatory provisions for Field Disturbance Sensors (FDS) and short-range radars.

60–64 GHz FMCW Radars (TI AWR6843ISK)

In the United States, unlicensed operation in the 57–71 GHz band is governed by 47 CFR § 15.255 (updated by the FCC in 2023 under ET Docket No. 21-264 specifically to accommodate short-range FMCW radars), while European operation is governed by ETSI EN 305 550 / EN 302 264:

  • EIRP & Chirp Duty-Cycle Rules (47 CFR § 15.255(c)(2)): Under FCC rules, field disturbance sensors (radars) operating across 57–64 GHz may transmit up to +20 dBm peak EIRP (100 mW) without duty-cycle restrictions. Radars operating in 60–64 GHz may also operate at higher peak EIRP (up to +36 to +42 dBm depending on installation) only if the radar’s transmit duty cycle (total chirp on-time) does not exceed 10% within any contiguous 33 ms interval (or up to +30 dBm peak / +14 dBm average EIRP in 57.0–61.5 GHz with a 50% duty cycle).
  • Schema Safeguards for .cfg Chirp Profiles: On the TI AWR6843ISK, each TX channel delivers ~+12 dBm conducted power into an ~8 dBi PCB patch antenna (~+20 dBm EIRP for 1 TX, or ~+26 dBm EIRP when all 3 TX antennas transmit simultaneously). When allowing users to upload custom TI mmWave .cfg chirp configurations, the driver schema should validate profileCfg and frameCfg parameters so that:
    1. Start and end frequencies stay strictly within 60.0–64.0 GHz;
    2. Active chirp time per frame remains ≤10% of the frame period (e.g., ≤3.3 ms of active ramp time per 33 ms frame); and
    3. Continuous-wave (contModeCfg) streaming is disabled.
  • Physical Propagation & Use Restrictions: Because 60 GHz signals experience strong atmospheric oxygen (O2) absorption (~10–15 dB/km) and high attenuation through drywall, concrete, and coated glass, indoor 60 GHz radar emissions remain naturally confined to the laboratory room. Note that § 15.255(b) restricts operation aboard aircraft or satellites.

24 GHz Narrowband ISM Radars (RFbeam K-MD7)

At 24 GHz, operators must distinguish between the narrowband 24.00–24.25 GHz ISM allocation (which is permitted) and legacy ultra-wideband (UWB) 22–29 GHz radar operation (which was phased out globally to protect passive weather satellites):

  • Strict Protection of the 23.6–24.0 GHz Passive Satellite Band: Immediately below 24.00 GHz lies the 23.6–24.0 GHz Earth Exploration-Satellite Service (EESS) passive water-vapor sensing band, which is a strictly protected 47 CFR § 15.205 restricted band (and ITU Radio Regulations Footnote 5.340 “all emissions prohibited” band). No fundamental or out-of-band sweep may ever extend below 24.00 GHz.
  • Permitted 24.00–24.25 GHz ISM Operation: Both FCC 47 CFR § 15.249 (up to 250 mV/m average at 3 meters, or ~+12.7 dBm average / +20 dBm peak EIRP), 47 CFR § 15.245 (for fixed field disturbance sensors in 24.075–24.175 GHz), and ETSI EN 300 440 (up to +20 dBm EIRP across 24.00–24.25 GHz) authorize narrowband 24 GHz radars inside the 250 MHz ISM window.
  • K-MD7 Pre-Configured Compliance: The RFbeam K-MD7 radar operates strictly within 24.075–24.175 GHz (providing a 75 MHz guard band above the 24.00 GHz passive band edge) at a factory-calibrated maximum EIRP of +19 to +20 dBm. Because sweep frequencies and RF output power on the K-MD7 are controlled by onboard radar firmware presets rather than arbitrary user IQ waveforms, users cannot command the K-MD7 outside its 24.075–24.175 GHz band.

International (Non-US) Considerations

If you deploy RemoteRF outside the United States, your node is governed by the national spectrum authority of the country where the physical radio hardware is located.

Critical Warning: The 902–928 MHz Band Is Americas-Only

Many RemoteRF educational examples and hardware guides reference the 902–928 MHz ISM band because RemoteRF originated in the United States. However, 902–928 MHz is an unlicensed ISM band only in ITU Region 2 (North and South America).

In Europe, the United Kingdom, Africa, and much of Asia and Oceania (ITU Regions 1 and 3), the 880–960 MHz range is allocated to licensed commercial cellular networks (E-GSM / LTE / 5G Band 8). Transmitting at 915 MHz over the air in Europe or Asia can cause direct interference to mobile carrier base stations and trigger immediate regulatory enforcement.

If you are deploying outside the Americas, use a cabled coaxial loopback setup or configure your OTA hardware filters, antennas, and software schemas for an unlicensed / Short-Range Device (SRD) band permitted in your jurisdiction (such as 2400–2483.5 MHz worldwide, 863–870 MHz in Europe/UK, or 433.05–434.79 MHz in ITU Region 1).

Jurisdiction Spectrum Authority Common Unlicensed / SRD Bands (Verify Local ERP & Duty-Cycle Limits)
United States FCC (47 CFR Part 15 / Part 5) 902–928 MHz, 2400–2483.5 MHz, 5725–5850 MHz, 24.0–24.25 GHz, 57–71 GHz
Canada ISED (RSS-210 / RSS-247) 902–928 MHz, 2400–2483.5 MHz, 5725–5850 MHz, 24.0–24.25 GHz, 57–71 GHz
European Union CEPT / ETSI (EN 300 220 / 300 440 / 305 550) & National Regulators 433.05–434.79 MHz, 863–870 MHz (strict ERP & duty-cycle limits), 2400–2483.5 MHz, 5725–5875 MHz, 24.0–24.25 GHz, 57–64 GHz (902–928 MHz is cellular Band 8 — prohibited)
United Kingdom Ofcom (IR 2030) 433.05–434.79 MHz, 863–870 MHz, 2400–2483.5 MHz, 5725–5850 MHz, 24.0–24.25 GHz, 57–64 GHz (902–928 MHz prohibited)
South Korea MSIT / RRA 917–923.5 MHz (narrow sub-band with strict LBT/power limits), 2400–2483.5 MHz, 5725–5825 MHz, 24.0–24.25 GHz, 57–64 GHz
Japan MIC (ARIB STD-T66 / T108) 920.5–928.1 MHz (strict LBT & duty-cycle rules), 2400–2483.5 MHz, 24.0–24.25 GHz, 57–66 GHz (Technical Conformity Mark / experimental license rules apply)
Australia ACMA (LIPD Class Licence) 915–928 MHz, 2400–2483.5 MHz, 5725–5850 MHz, 24.0–24.25 GHz, 57–66 GHz

Because unlicensed power ceilings, Equivalent Isotropically Radiated Power (EIRP), listen-before-talk (LBT) requirements, and duty-cycle limits (often 0.1% to 10% in the European 863–870 MHz band) vary significantly by country, always verify local regulations with your national spectrum authority and institutional compliance office before enabling over-the-air transmissions.